Land Rover Roof Racks
MCB 4x4 build steel roof racks by hand in the UK for the Land Rover Defender 90, 110, 130 and Discovery 1 and 2: flat racks, expedition racks with rails, half racks and roof tent racks, plus rear ladders and light mounts. Every rack is made to order for your vehicle.
Build your roof rack → Pick your vehicle, rack, finish, mesh and mounts, see it drawn, then add the whole build to your cart.
Racks by model: Defender 90, Defender 110, Defender 130, Discovery 1, Discovery 2.
A half-length roof rack for the Land Rover Defender 90, made by hand in steel and built to order. It's a smaller rack for carrying a few bits of gear, and it leaves the rest of the roof clear.
We're Land Rover specialists, so we can fit it too. Have it delivered free to the UK mainland, or book in at our workshop in Llandysul, West Wales and we'll fit it for £40. Each rack is welded by MCB 4x4, who have been building roof racks since 2004.
Construction
- Mild steel, hand welded
- Powder coated in satin black as standard (other finishes below)
- Lighter than most aluminium racks
- Made to fit the Defender 90
Options and extras
- Finish (choose above): black powder coat (RAL 9005) as standard; white (RAL 9016) or gunmetal grey (RAL 7016) +£20; Land Rover off white (RAL 9010) +£40; Land Rover colours +£80, each the closest RAL match to the original Land Rover paint code; any other colour +£120; galvanised +£150
- Mesh base: +£70 (choose above)
- Rear access ladder: £100
- Light / CB mounts: £12 each
- Awning mount plates, Hi-Lift jack mount plates and sand ladder mounts: £40 a pair
- Solid bases and custom mounts: message us for a price
Lead time
Every rack is made to order. Lead time: 3 - 5 weeks (Depending on Location). If you need something custom, get in touch before ordering.
See all Defender 90 roof racks.
A Xander roof rack for the Land Rover Defender 130 Crew Cab, made by hand in steel and built to order. It has side rails like an expedition rack, but the front and rear are left open, so long loads such as ladders or lengths of timber are easy to carry and tie down.
We're Land Rover specialists, so we can fit it too. Have it delivered free to the UK mainland, or book in at our workshop in Llandysul, West Wales and we'll fit it for £40. Each rack is welded by MCB 4x4, who have been building roof racks since 2004.
Construction
- Mild steel, hand welded
- Powder coated in satin black as standard (other finishes below)
- Lighter than most aluminium racks
- Made to fit the Defender 130 Crew Cab (cab only)
Options and extras
Design it your way: open this rack in our roof rack builder to choose the finish, mesh and mounts, place each mount on a drawing of the rack, and add the whole build to your cart in one go.
- Finish (choose above): black powder coat (RAL 9005) as standard; white (RAL 9016) or gunmetal grey (RAL 7016) +£20; Land Rover off white (RAL 9010) +£40; Land Rover colours +£80, each the closest RAL match to the original Land Rover paint code; any other colour +£120; galvanised +£150
- Mesh base: +£70 (choose above)
- Rear access ladder: £100
- Light / CB mounts: £12 each
- Awning mount plates, Hi-Lift jack mount plates and sand ladder mounts: £40 a pair
- Solid bases and custom mounts: message us for a price
Lead time
Every rack is made to order. Lead time: 3 - 5 weeks (Depending on Location). If you need something custom, get in touch before ordering.
See all Defender 130 roof racks.
Heavy duty luggage tie down D-ring, Land Rover part number EOZ500070, as used in the Freelander load area.
Gives a secure anchor point for straps and nets. Supplied with an M8 bolt, nut and washer.
Part number: EOZ500070
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
See the full DDS Metals range at LCM 4x4.
Bonnet latch nutsert for the Land Rover Defender, part number FRP100010.
A threaded insert used to mount the bonnet latch. Worth replacing when the original has spun or the thread is damaged, so the latch can be tightened down properly.
Fits: Land Rover Defender
Part number: FRP100010
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
See the full DDS Metals range at LCM 4x4.
Rear tub mounting angle with gussets for the Land Rover Defender, part number AQR710020. Made in the UK by DDS Metals.
The angle runs across the rear of the tub and holds the body to the chassis. A new one restores a solid mounting for the rear body.
Details: CNC profiled from 2mm aluminium, spot welded and black powder coated, made to OE specification.
Fits: Land Rover Defender rear tub
DDS part number: AQR710020
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
See the full DDS Metals range at LCM 4x4.
Rear tub light panel cover for the Land Rover Defender. Made in the UK by DDS Metals.
The cover fits inside the rear tub behind the rear light, protecting the light unit and its wiring from cargo and water.
Details: Made as an OE replacement in 1.2mm aluminium.
Fits: Land Rover Defender rear tub
Side: left or right (choose above). Left and right are as viewed sitting in the vehicle.
DDS part numbers: MTC7879 (left), MTC7878 (right)
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
See the full DDS Metals range at LCM 4x4.
Chequer plate bonnet protector for the Land Rover Discovery 3 and Discovery 4. Made in the UK by DDS Metals.
Protects the leading edge and top of the bonnet from stone chips, branches and boots when you are up on the bonnet loading the roof.
Details: CNC profile cut from 2mm aluminium chequer plate. Available in mill finish (bare aluminium) or black powder coated. Supplied with a rivet pack for fitting.
Fits: Land Rover Discovery 3 and Discovery 4
DDS part numbers: LRB360 (mill finish), LRB360B (black)
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
See the full DDS Metals range at LCM 4x4.
Rear sill for the Land Rover Series 2A long wheelbase. Made in the UK by DDS Metals.
Sills sit low along the side of the body, where they take knocks and collect mud and water. A new sill restores a clean, straight line along the side of the vehicle.
Details: Made as an OE replacement in 1.2mm aluminium, CNC laser cut and press tool formed for accuracy and consistency.
Fits: Land Rover Series 2A LWB (109")
Side: left or right (choose above). Left and right are as viewed sitting in the vehicle.
DDS part numbers: 337933 (left), 337932 (right)
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
See the full DDS Metals range at LCM 4x4.
AVM style 24 spline free wheeling (locking) hubs for the Land Rover Defender and Discovery 1 from 1994, and for Series vehicles with the LOF 24 spline disc brake conversion.
Free wheeling hubs let you disconnect the front wheels from the drive shafts. On the road the front diff and shafts stop turning, which cuts drag and wear. If a front drive shaft breaks off-road, disengage the hubs and drive on in 2WD.
Specifications
Spline: 24
Material: corrosion resistant alloy with heat treated steel clutch ring
Operation: manual knob, 4x2 or 4x4
Wheels: steel wheels only
What's Included
Pair of free wheeling hubs
LT230 transfer box conversion kit (not needed on Series vehicles)
Fits
Land Rover Defender (1994 onwards) with 24 spline axles
Land Rover Discovery 1 (1994 onwards) with 24 spline axles
Land Rover Series 88" and 109" with the LOF 24 spline disc brake conversion
Good to Know
These hubs will not fit with factory alloy wheels.
Grease them regularly to keep them working smoothly.
See the full LOF Clutches range at LCM 4x4.
A 52mm hub nut box spanner, part number 606435, for removing and fitting the wheel bearing hub nuts.
Needed whenever you change wheel bearings, hub seals or stub axles.
Specifications
Part number: 606435
Size: 52mm
Fits
Land Rover Series
Land Rover Defender
Land Rover Discovery 1
Range Rover Classic
See the full LOF Clutches range at LCM 4x4.
A set of eight seal drivers for fitting gearbox, axle, hub and transfer box seals on Land Rovers, designed by LOF.
Each driver is CNC machined from tough, oil resistant nylon, so it will not mark alloy housings, and is shaped to seat the seal square at the correct depth. The set comes with a handle and a wall mounted stainless steel holder.
What's Included
1x aluminium tool handle
FTC4851 Defender differential pinion oil seal driver
FTC5258 differential oil seal driver
STC4401 Salisbury rear differential oil seal driver
ICV100000 LT230 transfer box input seal driver
LR0058800 TDCi Puma MT82 rear output seal driver
FTC4785 wheel hub oil seal driver (post 1994 Defender, Discovery 1, Range Rover Classic)
FTC4939 LT230 rear output seal driver
FTC4939 LT230 front output seal driver
Wall mounted machined stainless steel tool holder
Fits
Land Rover Defender, Discovery 1 and Range Rover Classic, including 300Tdi, Td5 and TDCi Puma drivetrains
See the full LOF Clutches range at LCM 4x4.
Land Rover STC50550 RTV gasket sealant, for making a durable seal between two components.
Recommended when fitting the HD rear crank seal (MWM 70730056) on the 300Tdi.
Specifications
Part number: STC50550
See the full LOF Clutches range at LCM 4x4.
A pair of gearbox mounts, part number ANR1808, made to OEM specification from oil and fuel resistant rubber.
Worn mounts let the gearbox and transfer box move under load, which shows up as clunks, vibration and extra strain on the propshafts. Replace both sides together so the load is shared evenly.
Specifications
Part number: ANR1808
Quantity: 2 (pair)
Fits
Land Rover Defender 90, 110 and 130 (LT77, R380 and automatic)
Land Rover Discovery 1 (1989 to 1998)
Range Rover Classic (1986 to 1995)
See the full LOF Clutches range at LCM 4x4.
Corteco front cover input shaft oil seal for the LT77 and R380 manual gearboxes, part number FTC5303.
Made from FPM (Viton) for good heat and oil resistance. A leaking input seal lets gearbox oil onto the clutch, so it is worth changing whenever the gearbox and clutch are apart.
Specifications
Part number: FTC5303
Material: FPM (Viton)
Brand: Corteco
Fits
Land Rover Defender with LT77 or R380
Land Rover Discovery 1 with LT77 or R380
Land Rover Discovery 2 with R380
Range Rover Classic with LT77 or R380
Range Rover P38 with R380
See the full LOF Clutches range at LCM 4x4.
Corteco input shaft oil seal for the LT230 transfer box and the LT77 and R380 extension cases used with the 5 speed manual gearboxes, part number ICV100000.
It seals the input shaft to stop gearbox or transfer box oil leaking out. Replace it whenever the transfer box is separated from the gearbox.
Specifications
Part number: ICV100000
Replaces: FRC2365
Brand: Corteco
Fits
Land Rover Defender (1987 to 2006), mainshaft gear
Land Rover Discovery 1 (1989 to 1998), 5 speed manual extension case
Land Rover Discovery 2 (1998 to 2004), mainshaft gear
See the full LOF Clutches range at LCM 4x4.
Corteco rear crankshaft oil seal for the Land Rover Defender 2.4 and 2.2 TDCi (Puma), part number LR020610.
A leaking rear main seal lets engine oil into the bellhousing, where it soaks the clutch friction plate. It is good practice to replace it whenever the clutch or flywheel is out.
Specifications
Part number: LR020610
Brand: Corteco (OE quality)
Fits
Land Rover Defender 90, 110 and 130 TDCi Puma 2.4 and 2.2 (2007 to 2016)
Good to Know
Do not remove the alignment sleeve until the seal is fully installed.
Do not use grease or oil on the seal.
Fit the seal carrier within five minutes of applying sealant, and follow the Land Rover procedure for sealant and bolt sequence.
See the full LOF Clutches range at LCM 4x4.
A set of 8 flywheel bolts for the 4 cylinder Land Rover 200Tdi and 300Tdi engines, part number ERR4574.
Flywheel bolts are stretch bolts and should be replaced whenever the flywheel is removed. These come pre-coated with Loctite.
Specifications
Part number: ERR4574
Quantity: 8 bolts
Thread locker: pre-coated
Fits
Land Rover Defender, Discovery 1 and Range Rover Classic with 200Tdi or 300Tdi
Good to Know
Torque to the Land Rover figure for your engine.
See the full LOF Clutches range at LCM 4x4.
Banjo bolt for the clutch master cylinder STC500100 on the Land Rover Defender Td5 and TDCi, part number SYG500020.
Worth replacing along with the master cylinder or when the old bolt is corroded or the sealing faces are damaged.
Specifications
Part number: SYG500020
Fits master cylinder: STC500100
Fits
Land Rover Defender Td5
Land Rover Defender TDCi 2.4 and 2.2
Good to Know
Use new sealing washers and bleed the clutch after fitting.
See the full LOF Clutches range at LCM 4x4.
Genuine Land Rover clutch switch for the Defender TDCi and Discovery 2 Td5, part number MSK500020.
The switch sits above the clutch master cylinder on the banjo fitting to the clutch pipe and tells the engine management when the clutch is pressed.
Specifications
Part number: MSK500020
Brand: Genuine Land Rover
Fits
Land Rover Defender TDCi 2.4 and 2.2
Land Rover Discovery 2 Td5
See the full LOF Clutches range at LCM 4x4.
Genuine Land Rover clutch switch for the Defender Td5, part number MSK500010.
The switch sits above the clutch master cylinder on the banjo fitting to the clutch pipe and tells the engine management when the clutch is pressed. A faulty switch can cause hesitation or surging when changing gear.
Specifications
Part number: MSK500010
Brand: Genuine Land Rover
Fits
Land Rover Defender Td5
See the full LOF Clutches range at LCM 4x4.
Land Rover roof racks, handmade in the UK
Every roof rack here is built by hand from steel by MCB 4x4, who have been making Land Rover roof racks since 2004. Racks are made for the Land Rover Defender 90, 110 and 130, Discovery 1 and Discovery 2. Each one is made to order and powder coated in satin black. They are lighter than most aluminium racks. We're Land Rover specialists, so we can fit it too: delivery is free to the UK mainland, or book in at our workshop in Llandysul, West Wales and we'll fit it for £40.
Which roof rack do you need?
Flat roof rack. Exactly what it sounds like: a flat platform with nothing above the base of the rack. It sits around 50mm above the roof, so you can still use multi-storey car parks and most garages, and makes a strong base for a roof tent, roof box, sand ladders or general gear. Defender 90 · Defender 110 · 110 Crew Cab · 130 Crew Cab · 130 Full Length · Discovery 1 · Discovery 2
Expedition roof rack. Has an upper rail around the whole rack. This makes it easier to keep smaller boxes, bags and jerry cans on the roof, but it adds height. Defender 90 · Defender 110 · 110 Crew Cab · 130 Crew Cab · Discovery 1 · Discovery 2
Roof tent rack. Has an upper rail around the front only, so it sits halfway between a flat rack and an expedition rack. The front rail protects the tent from branches. Defender 90 · Defender 110 · Discovery 2
Half roof rack. A smaller rack, useful when you only need to carry a few bits, such as a spare wheel, a roof box or lights, leaving the rest of the roof clear. Defender 90 · Defender 110 · Discovery 1 · Discovery 2
Xander roof rack. Upper rails like the expedition rack, but on the sides only. The front and rear are left open, so it is easy to carry and tie down things longer than the rack, such as ladders or lengths of timber. Defender 90 · Defender 110 · 110 Crew Cab · 130 Crew Cab
Which racks fit my vehicle?
Defender 90: flat, expedition, roof tent, half and Xander
Defender 110: flat, expedition, roof tent, half and Xander
Defender 110 Crew Cab / 130: flat, expedition and Xander
Discovery 1: flat, expedition and half
Discovery 2: flat, expedition, roof tent and half
Need a Land Rover rack that isn't listed? It can still be made to order. Message us for a price.
Extras
Any rack can have a mesh base (+£90), a rear access ladder (£100) and light and CB aerial mounts (£12 each). Awning, sand ladder and Hi-Lift jack mounts, solid bases and custom mounts can be made too. Message us for a price.
Roof rack questions
Will a flat roof rack fit in a multi-storey car park?
The flat racks sit around 50mm above the roof, so you can still use multi-storey car parks and most garages. Expedition, roof tent and Xander racks are taller because of their upper rails.
Which rack should I choose?
Go flat if you want a low platform with nothing above the base. Go expedition if you carry smaller boxes, bags or jerry cans and want a rail all the way round. The roof tent rack has a rail around the front only, to protect the tent from branches. If you carry long items like ladders or timber, the Xander rack has side rails with an open front and rear.
How long does a rack take?
Every rack is made to order. Lead time is 3-5 Weeks (Depending on Location).
Can you fit the rack for me?
Yes. Book in at our workshop in Llandysul, West Wales and we will fit it for £40. Otherwise delivery is free to the UK mainland.
Can I have something custom?
Yes. If you need custom mounts or something a bit different, get in touch before ordering and we will come back to you with a price.
A full-length flat roof rack for the Land Rover Defender 130 Crew Cab, made by hand in steel and built to order. One rack runs over the cab and carries on over the truck bed, with rear legs that drop down to the bed sides to support the back. Nothing sits above the base, so it stays low.
We're Land Rover specialists, so we can fit it too. Have it delivered free to the UK mainland, or book in at our workshop in Llandysul, West Wales and we'll fit it for £40. Each rack is welded by MCB 4x4, who have been building roof racks since 2004.
Construction
Options and extras
Design it your way: open this rack in our roof rack builder to choose the finish, mesh and mounts, place each mount on a drawing of the rack, and add the whole build to your cart in one go.
Lead time
Every rack is made to order. Lead time: 3 - 5 weeks (Depending on Location). If you need something custom, get in touch before ordering.
See all Defender 130 roof racks.