Chassis & Frame Parts
Rear Grab Handle Bolt Kit (NTC5116), Stainless for the Land Rover Series and Defender. Made in the UK by DDS Metals.
Strong, properly mounted recovery points are essential for safe off-road recovery. These DDS parts give you a secure anchorage designed for the job.
Details: Stainless steel fixings for rust prevention fits the rear handles to the crossmembers suitable for Series I – II – III & Defender models.
Fits: Land Rover Series and Defender
DDS part number: BKNTC5116SS1
Land Rover part number (for reference): NTC5116
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender Rear Crossmember Twin Tube Anti-Crush Spacer for the Land Rover Defender. Made in the UK by DDS Metals.
The rear crossmember takes towing loads and holds the back of the body, and it traps mud and water along its top and ends. Rot here is one of the most common Land Rover chassis repairs. A new crossmember or end section restores strength for towing, recovery points and the rear body mounts.
Details: Made from 19mm tube with a 3mm wall, cut to length, allowing up to a 12mm bolt to pass through so you can bolt up properly without crushing the crossmember.
Fits: Defender
Finish (choose above): Plain – plain steel, ready for your own paint or underseal; Galvanised – hot-dip galvanised for long-term corrosion protection.
DDS part numbers: ANR3821, ANR3821G
Land Rover part numbers (for reference): ANR3821, KVX000020
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Series LWB Gearbox Crossmember for the Land Rover Series 2, 2A and 3 109" LWB. Made in the UK by DDS Metals.
Crossmembers tie the chassis rails together and carry key mounting points. Because they collect mud and moisture, they often corrode long before the main rails. Replacing a rotten crossmember restores the stiffness and safety of the chassis.
Fits: Land Rover Series 2, 2A and 3 109" LWB
DDS part number: LR10B
Land Rover part number (for reference): 592592
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Lower radiator mounting bracket for the Land Rover Defender Td5 and Puma. Made by DDS Metals.
The lower radiator brackets sit right at the front of the chassis and take the full force of water, mud and salt, so they're often badly corroded. New brackets give the radiator a solid, rattle-free mounting.
Fits: Land Rover Defender Td5 and Puma
Side: left or right (choose above)
DDS part number: LR633
Not sure if this suits your vehicle? Get in touch with your vehicle details and we'll confirm fitment before you order.
Defender 110 / 130 Td5 Rear Half Chassis (1600mm Legs) for the Land Rover Defender 110 and 130 Td5. Made in the UK by DDS Metals.
The rear of a Land Rover chassis takes the worst of the water, salt and mud thrown up by the rear wheels. Rather than replacing the whole chassis, a rear section can be grafted onto sound front rails, saving a great deal of time and money while restoring full strength.
Details: Once fitted, we recommend treating the inside of the chassis with Waxoyl or similar.
Fits: Land Rover Defender 110 and 130 Td5
Finish (choose above): Black powder coated – black powder coated, ready to fit; Galvanised – hot-dip galvanised for long-term corrosion protection.
DDS part numbers: LR617, LR617G
Former Bearmach part number: BA8424
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender 110 Tdi Rear Half Chassis (1600mm Legs) for the Land Rover Defender 110 200Tdi and 300Tdi, 1984-1997. Made in the UK by DDS Metals.
The rear of a Land Rover chassis takes the worst of the water, salt and mud thrown up by the rear wheels. Rather than replacing the whole chassis, a rear section can be grafted onto sound front rails, saving a great deal of time and money while restoring full strength.
Details: Once fitted, we recommend treating the inside of the chassis with Waxoyl or similar.
Fits: Land Rover Defender 110 200Tdi and 300Tdi, 1984-1997
Finish (choose above): Black powder coated – black powder coated, ready to fit; Galvanised – hot-dip galvanised for long-term corrosion protection.
DDS part numbers: LR414, LR414G
Former Bearmach part number: BA8423
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender 110 V8 / Military Rear Half Chassis (1600mm Extensions) for the Land Rover Defender 110 V8, Tdi and military (oval electric hook-up hole). Made in the UK by DDS Metals.
The rear of a Land Rover chassis takes the worst of the water, salt and mud thrown up by the rear wheels. Rather than replacing the whole chassis, a rear section can be grafted onto sound front rails, saving a great deal of time and money while restoring full strength.
Details: Please state whether your vehicle has folded or flat tabs on the crossmember ot stocked this product is made to order, lead time 7-10 days ot to be confused with a Wolf this is not for Wolf.
Fits: Land Rover Defender 110 V8, Tdi and military (oval electric hook-up hole)
DDS part number: LR448
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender 50th Anniversary Rear Half Chassis (1400mm Legs) for the Land Rover Defender 90 50th Anniversary (V8). Made in the UK by DDS Metals.
The rear of a Land Rover chassis takes the worst of the water, salt and mud thrown up by the rear wheels. Rather than replacing the whole chassis, a rear section can be grafted onto sound front rails, saving a great deal of time and money while restoring full strength.
Fits: Land Rover Defender 90 50th Anniversary (V8)
DDS part number: LR419
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender 90 V8 / Military Rear Half Chassis (1400mm Extensions) for the Land Rover Defender 90 V8, Tdi and military (oval electric hook-up hole). Made in the UK by DDS Metals.
The rear of a Land Rover chassis takes the worst of the water, salt and mud thrown up by the rear wheels. Rather than replacing the whole chassis, a rear section can be grafted onto sound front rails, saving a great deal of time and money while restoring full strength.
Details: Please state whether your vehicle has folded or flat tabs on the crossmember ot stocked this product is made to order, lead time 7-10 days ot to be confused with a Wolf this is not for Wolf.
Fits: Land Rover Defender 90 V8, Tdi and military (oval electric hook-up hole)
DDS part number: LR444
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Series 2A Optional Steering Damper Bracket for the Land Rover Series 2A. Made in the UK by DDS Metals.
Steering brackets and mounts must be solid and correctly aligned. Corrosion or cracking around the steering box, damper or column mounts affects steering feel and safety.
Details: Made to OE specification.
Fits: Land Rover Series 2A
Finish (choose above): Black powder coated – black powder coated, ready to fit; Galvanised – hot-dip galvanised for long-term corrosion protection.
DDS part numbers: 552356, 552356G
Land Rover part number (for reference): 552356
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Body Mounting Spacer Tube (Range Rover Classic, Discovery 1 & 2) for the Range Rover Classic, Discovery 1 and Discovery 2, 1970-2004. Made in the UK by DDS Metals.
Body mounts carry the weight of the body on the chassis. When they corrode, the body can sag, panels stop lining up and doors become hard to shut. A new mounting bracket restores a solid, correctly located fixing point.
Details: Made to OE specification: 3mm steel with CNC turned tube and a zinc coated finish.
Fits: Range Rover Classic, Discovery 1 and Discovery 2, 1970-2004
DDS part number: KVH100030
Land Rover part number (for reference): KVH100030
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender & Series Rear Crossmember Stainless Steel Bolt Kit for the Land Rover Defender 90, 110 and 130, 1984-2016, and Series 3. Made in the UK by DDS Metals.
The rear crossmember takes towing loads and holds the back of the body, and it traps mud and water along its top and ends. Rot here is one of the most common Land Rover chassis repairs. A new crossmember or end section restores strength for towing, recovery points and the rear body mounts.
Details: Stainless steel fixing kits for fitting the rear body rail to the rear crossmember: M8 x 25mm screws (cap head, hex head or Torx head to suit the year), M8 nyloc nuts and M8 washers.
Fits: Land Rover Defender 90, 110 and 130, 1984-2016, and Series 3
Version: choose the kit to suit your vehicle's year and rear crossmember.
DDS part numbers: BKRXMSS1, BKRXMSS2, BKRXMSS3, BKRXMSS4
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
PTO Hole Socket Mounting Plate for the Land Rover. Made in the UK by DDS Metals.
Brackets like this are easy to overlook but often corrode or crack, especially on vehicles used off-road or in winter. A new DDS bracket restores a strong fixing point.
Details: Made to OE specification.
Fits: Land Rover
DDS part number: 562724
Land Rover part number (for reference): 562724
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender 110 Rear Floor Crossmember Assembly (4 & 5 Door, 2007-2016) for the Land Rover Defender 110 Puma / TDCi, 4 and 5 door, 2007-2016. Made in the UK by DDS Metals.
Crossmembers tie the chassis rails together and carry key mounting points. Because they collect mud and moisture, they often corrode long before the main rails. Replacing a rotten crossmember restores the stiffness and safety of the chassis.
Details: Fits onto the centre of the Defender, underneath the rear tub. Made to OE specification from 2mm steel, laser cut and pressed.
Fits: Land Rover Defender 110 Puma / TDCi, 4 and 5 door, 2007-2016
Version: Galvanised, as OE, With bolt-on brackets (choose above).
The bolt-on bracket version makes it easier to change the old body crossmember without removing the whole body.
DDS part numbers: KVB500230, KVB500230B/O
Land Rover part number (for reference): KVB500230
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
A-Frame to Body Bracket Nut Retaining Plate for the Land Rover Defender. Made in the UK by DDS Metals.
Brackets like this are easy to overlook but often corrode or crack, especially on vehicles used off-road or in winter. A new DDS bracket restores a strong fixing point.
Details: Nut retaining plate for A-Frame (chassis) to body bracket 2 projection welded nuts (M6) on a base plate & zinc plated.
Fits: Land Rover Defender
DDS part number: AFP710440
Land Rover part number (for reference): AFP710440
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender 300Tdi Gearbox Crossmember to Chassis Fixing Kit, A4-80 Stainless for the Land Rover Defender 300Tdi. Made in the UK by DDS Metals.
Crossmembers tie the chassis rails together and carry key mounting points. Because they collect mud and moisture, they often corrode long before the main rails. Replacing a rotten crossmember restores the stiffness and safety of the chassis.
Details: A4-80 stainless steel high tensile strength fixings fits the gearbox crossmember to the chassis (LR595) ANR3713.
Fits: Land Rover Defender 300Tdi
DDS part number: BKGB2C300TDISS1
Land Rover part number (for reference): ANR3713
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
A-Frame to Chassis Fixing Kit 3/4" UNF, Zinc Plated for the Land Rover Defender, Discovery 1 and Range Rover Classic. Made in the UK by DDS Metals.
Brackets like this are easy to overlook but often corrode or crack, especially on vehicles used off-road or in winter. A new DDS bracket restores a strong fixing point.
Fits: Land Rover Defender, Discovery 1 and Range Rover Classic
DDS part number: BKAF2CSS1
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender 200Tdi Gearbox Crossmember to Chassis Fixing Kit, A4-80 Stainless for the Land Rover Defender 200Tdi. Made in the UK by DDS Metals.
Crossmembers tie the chassis rails together and carry key mounting points. Because they collect mud and moisture, they often corrode long before the main rails. Replacing a rotten crossmember restores the stiffness and safety of the chassis.
Details: Suitable for fitting the gearbox crossmember (LR515) NTC9262 to the chassis A4 -80 stainless steel high tensile strength fixings.
Fits: Land Rover Defender 200Tdi
DDS part number: BKGB2C200TDISS1
Land Rover part number (for reference): NTC9262
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Defender 90 Tubular Outrigger to Tub Bolt Kit, A4-80 Stainless for the Land Rover Defender 90. Made in the UK by DDS Metals.
Outriggers carry the body and bulkhead mounts out from the main chassis rail and sit right in the spray thrown up by the wheels, so they are one of the first parts of a Land Rover chassis to rot. A corroded outrigger is a common MOT failure and lets the body move on its mounts; a new one restores a solid mounting point.
Details: A4-80 stainless steel high tensile fixings that fit the tub to the tubular outrigger (LR529N/S and LR529O/S).
Fits: Defender 90
DDS part number: BKTO2TSS1
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Series 3 Battery Frame, Galvanised for the Land Rover Series 3. Made in the UK by DDS Metals.
Fits: Land Rover Series 3
Engine: Diesel, Petrol (choose above).
DDS part numbers: LR108D, LR108P
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.
Series & Defender Rear Crossmember Grab Handle for the Land Rover Series & Lightweight, Defender. Made in the UK by DDS Metals.
The rear crossmember takes towing loads and holds the back of the body, and it traps mud and water along its top and ends. Rot here is one of the most common Land Rover chassis repairs. A new crossmember or end section restores strength for towing, recovery points and the rear body mounts.
Details: Rear grab handle for Series & Defender crossmembers TC5116 fits series 1 Series 2 Series 2A Series 3 defender 90, 110, 130, Tdi, Td5, Tdci/Puma .
Fits: Series & Lightweight, Defender
DDS part number: NTC5116
Land Rover part number (for reference): NTC5116
Not sure this is the right part for your vehicle? Get in touch with your vehicle details or VIN and we'll confirm fitment before you order.